Follow along with the video below to see how to install our site as a web app on your home screen.
Nota: This feature may not be available in some browsers.
En el titulo dices que estas decepcionado con la precisión, para algunos +7 segundos pueden ser mucho y para otros poco. Como bien han comentado incluso los Rolex nuevos con certificado COSC pueden venir mal ajustados. A mi si un reloj me decepciona lo vendo así de claro.
Con respecto al tamaño, lo veo normal tirando a grandecito para una muñeca de 16.5cm
Con la precisión nos obsesionamos un poco. Considerando que yo cambio de reloj cada 5 dias, desviaciones incluso de 20 segundos no me molestan, total cuando lo deje en la caja y le toque otra vez tendré que cambiar hasta el dia porque habrán pasado 20-30 dias. Incluso siendo tu único reloj no lo veo mal del todo, en 60 dias 7 minutos...es de lo más normal.
Tu mismo.
Es un gran reloj, eso sí a mi también me sorprendió que el Sumo tuviese más presencia, más grande y grueso aunque el armis del MM es muy superior y macizo. El cierre es de titanio por eso tiene otro tono. No te comas la cabeza con la precisión por que también influye mucho el tipo de trato que le des, y los meneos en el trabajo o de llevarlo al gym, disfrútalo si te gusta que para eso es.No me ha decepcionado el reloj en general,es un reloj precioso y pienso que es uno de los diver más bonitos que se pueden comprar.Unicamente no veo de recibo que venga tan mal ajustado.Te aseguro que no pienso venderlo.
es más,no consigo quitármelo de la muñeca
No me ha decepcionado el reloj en general,es un reloj precioso y pienso que es uno de los diver más bonitos que se pueden comprar.Unicamente no veo de recibo que venga tan mal ajustado.Te aseguro que no pienso venderlo.
es más,no consigo quitármelo de la muñeca
Qué curioso. Ayer discutía yo con Jonymd acerca de este tema en este hilo e insistía en no darle imporancia a que no fuera un calibre con certificación de precisión de ningún tipo...
https://relojes-especiales.com/threads/avenger-seawolf-o-marinemaster-sbdx001.343446/
Efectivamente, no tiene importancia hasta que te toca la china, y ya te digo que no eres ni el primero ni el segundo. Ahora busca un relojero que te lo quiera abrir (por la esfera) y ajustar si esa desviación (que tampoco es tan excesiva) te preocupa
Seiko especifica la precisión de estos relojes entre -15 y +25. por lo que tampoco te lo tendría por que ajustar por SAT
Amigo, este reloj si lo abren es en la casa,es Japón, aquí ningún concesionario oficial te lo abrirá
Buenas noches,hace unos 18 días que me llego el marinemaster 300m,llevaba tiempo detrás y al final lo compré.No me arrepiento en absoluto,el reloj es precioso.Lo primero que me sorprendió fue su tamaño,muy pequeñito,lo cual agradece mi muñeca de 16,5cm.
Para ser honesto no me gustaron dos cosas,la primera el cierre que lleva,da sensación de baja calidad,con la mariposa de chapa,en vez de ser maciza.
Y lo segundo el ajuste del reloj,esto sí que me fastidia.En 14 días que lo llevo puesto me adelantó un 1m40s.Es decir unos 7 segundos al día,y parece que pasando los días va un poquito a más.
No entiendo como un reloj con este calibre que dicen es muy bueno y el precio que tiene no viene mejor ajustado de fábrica.Y me puedo dar con un canto en los dientes,porque por lo visto las primeras unidades venían muy mal ajustadas hasta +15 o más.
La pregunta es,pierdo la garantía si lo abro para ajustarlo? O tengo que esperar dos añitos a que pase?
Me gustaría que los foreros que tienen este modelo me digan como les vino de ajustado de fábrica.He leído por el foro que algunos vienen a +1, me toco la China a mi?
Un saludo.
Y por cierto, ese reloj no se puede "abrir" tan fácilmente, pues al ser caja monobloque la única manera de acceder a la maquinaría es quitando el cristal.
Ahora busca un relojero que te lo quiera abrir (por la esfera) y ajustar si esa desviación (que tampoco es tan excesiva) te preocupa
Amigo, este reloj si lo abren es en la casa,es Japón, aquí ningún concesionario oficial te lo abrirá
[FONT=Trebuchet MS, Trebuchet]Todays victim, ain't she purtty.................................
I case you dont know the story, let me bring you up to speed. Long time ago I owned one of the first MM`s, back in 2002. At that time I had pulled off the bezel and had a look see at what there was. What I saw on the crystal retainer at that time made it perfectly clear it required a special wrench to gain access to the movement. So I never went any further in trying to open one. There were more then enough vintage watches to keep busy also,
Now, a few years has gone by and Seiko has changed how this baby is put together, and now I don't need no special stinking tool to get into them. This is a late model 2008 watch, where the change over date is (For the crystal retainer design) I do not know, but I know enough to know now that I`ll be able to get into all of them, I may need to make a wrench for the earlier ones, but thats part of the fun,
OK, So lets get to it,
Whenever I`m working on a watch such as this, she gets protected.................
The bezel pops off easily enough, not more trouble then a SKX diver.
So with that I can see the newer crystal retainer. You` notice I have tapped over the crystal also, and this is what I do on most case backs also before I remove them, I`v just found its too easy and really saves your hide if you slip,
It is not the inner set of lug notches that we need to put the removal tool on (They retain the crystal itself), but the outer set of notches that retain the entire crystal assembly and bolt it to the case just like a case back! Not only that, but the outer ring that comprises the case seal is "Left Hand" thread!! So by turning "Right", it unscrews as easily and as simply as any other case back should,Previously, I had seen two small flats, and no outer notches on the earlier watches,
Here is a shot of the hold over lands for the earlier wrench, there are two lands like this directly opposite of each other.
OK, crystal ring is out, very far out looking sitting by itself.......................
And turned over. The flats or lands for the earlier wrench are more noticable here.
And this next picture will show you how it bolts down on a standard O-ring gasket in a channel, just like a case back.
I`ll say, the machine work here is absolutely phenomenal. Everything is beyond just being stately and workman like here in this machining , its more polished and perfect! The tolerances and polish and attention to detail here are much closer then you would find in a "everyday" Seiko. This case IS, a WORK OF ART!
Another angle...................................................
And heres our stem release, right at 3 O`clock.
Removing the dial trim ring, it simply lifts off at this stage, gives a little more room to work the steam release......................................
And so that gives us a look at the Marine Masters crown and tube.
OK, I hate to say this, but this crown is anemic. This is no better crown then you will find on a Sumo or even a monster. Its only using one gasket, appears to be the same gasket used on the SKX!! Really sad about this. I would have thought Seiko would use at least two or three gaskets in this, but there is only the one! One stinking gasket!! No back up, its not even large by any stretch of the word. Ohh well. Lets put a trip lock on it! LOLLOLOLOL.
A few more shots of the crown.
Lets move on. To the empty case. In this case, the machine work still impress`s!
There is a thin rubber o-ring at the very bottom of the well you can see. This works as the case spring, butting up against the movement holder and taking up (gently) any slack in the over all height of the internal parts . When you are re-assembling the movement in the case, you have to be very careful not to let this o-ring get up under the movement, or it will interfere with the winding rotor being able to spin.
And now the movement as she sits removed from the case........
And now the back side, always the prettiest part,
[/FONT]
Prueba a comentarlo en un SAT Seiko, a ver si le dan ajuste.
Abrir la caja monobloque no es difícil... si se sabe cómo, se hace con una llave convencional de fondos roscados, sólo que por delante una vez quitado el bisel. Un tal Dr. Seiko en Seikoholics. La tija saldría apretando un botoncito.
Hola.Buenas noches,hace unos 18 días que me llego el marinemaster 300m,llevaba tiempo detrás y al final lo compré.No me arrepiento en absoluto,el reloj es precioso.Lo primero que me sorprendió fue su tamaño,muy pequeñito,lo cual agradece mi muñeca de 16,5cm.
Para ser honesto no me gustaron dos cosas,la primera el cierre que lleva,da sensación de baja calidad,con la mariposa de chapa,en vez de ser maciza.
Y lo segundo el ajuste del reloj,esto sí que me fastidia.En 14 días que lo llevo puesto me adelantó un 1m40s.Es decir unos 7 segundos al día,y parece que pasando los días va un poquito a más.
No entiendo como un reloj con este calibre que dicen es muy bueno y el precio que tiene no viene mejor ajustado de fábrica.Y me puedo dar con un canto en los dientes,porque por lo visto las primeras unidades venían muy mal ajustadas hasta +15 o más.
La pregunta es,pierdo la garantía si lo abro para ajustarlo? O tengo que esperar dos añitos a que pase?
Me gustaría que los foreros que tienen este modelo me digan como les vino de ajustado de fábrica.He leído por el foro que algunos vienen a +1, me toco la China a mi?
Un saludo.
Los Ananta, spring drive y ciertos modelos como este los mandan a japon. Si aun lo tiene cuando se quede sin garantía q vaya a un relojero independiente que haya trasteado estos relojes. No es difícil. Por +7 no lo mandaba al Sat, ojo es mi opinión. Cada uno que haga lo que le venga en gana
El marinemaster te lo abren en el sat en España sin problemas, no entiendo como podeis afirmar estas cosas tan alegremente.Amigo, este reloj si lo abren es en la casa,es Japón, aquí ningún concesionario oficial te lo abrirá
prueba a cambiar de posición al dejarlo de noche, como bien te comentó un compañero, boca arriba suelen atrasar.